350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11160109 67-69 GM “F” Body Complete CoilOver Sy
Installation Instructions Driver Side Top View 1. On some cars, to remove the upper control arm you mu
These Strong Arms come equipped with a changeable caster slug setup. This allows you to add or remove caster from the fro
Item # Description Qty. 1. Passenger side arm 1 1. Driver side arm (Shown) 1 2. Extension stop 2 3. Ball
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com 11009300 GM “A” & “F” Body Tall Spindles 2 T
INSTRUCTIONS FOR Ridetech Tall SPINDLES These spindles will fit ’67-69 Camaro, ’64-’72 Chevelle, and ’68-’74 Nova. They will provide a 2” drop, and
Disassembly of the ball joints from the spindles can be eased by making the simple tool shown in the photo below. A pair of 1 ½” long bolts are th
If you remove the calipers but leave the hoses attached, supporting them to avoid stressing the hoses, you won’t even need to rebleed the brakes!
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11167199 67-69 GM “F” Body AirBar Components:
1. Raise the vehicle to a safe and comfortable working height. Use jack stands to support the vehicle with the suspension hanging freely. 2. S
8. The lower axle bracket will be fastened to the leaf spring pad using the factory T-bolts. The bar mount i
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11163509 67-69 GM “F” Body Non-Adjustable Front
12. How do you set the pinion angle? On a single-piece shaft you want to set it up where a line drawn through the center of the eng
Upper Bar Installation Jig This jig has been supplied to aid in the installation of the upper 4 link bar. It can be temporarily used to properly
15. One helpful trick to help maintain ride height and pinion angle while adjusting is to tack weld a spacer between the axle and the outside
Should I weld my AirBar 4 link assembly in? Since we get this question quite often, it deserves a proper explanation. The
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11166509 67-69 GM “F” Body Non-Adjustable Rear
1. Impact Forged, Monotube shock 2. Rebound adjustment knob (SA Only) 3. Upper coil spring
1. Inspect the factory welds attaching the upper shock bracket to the frame. Re-weld if necessary. 2. To allow the step in the lower
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11162899 67-69 GM “F” Body & 68-74 GM “X” B
Installation Instructions 1. After removing the factory lower control arm, clean the bushing mounting surfaces on the frame and lubri
7. Screw a 3/8” x 1 ¼” bolt and nut into the hole in the side of the lower arm. This will act as an adjustable steering st
Item # Description Qty. 1. Passenger side arm 1 1. Driver side arm 1 2. Aluminum bearing spacer 4 3. Ball
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11163699 67-69 GM “F” Body & 68-74 GM “X” B
Comments to this Manuals